衬氟18dj18大奖娱乐手机系列   蝶阀系列   平板18dj18大奖娱乐手机系列   球阀系列   水力控制阀系列   脱硫18dj18大奖娱乐手机系列   18dj18大奖娱乐手机系列   截止阀系列   止回阀系列  
蝶阀系列产品
中线蝶阀
中线蝶阀1
法兰中线蝶阀
伸缩蝶阀
软密封偏心法兰蝶阀
蝶形止回阀
全塑蝶阀
沟槽式蝶阀
 
软密封偏心法兰蝶阀
先进性体现Guaranteed performance
概述General
双偏心软密封蝶阀是通过蝶板作90℃旋转而进行启闭的一种18dj18大奖娱乐手机,它不仅可用作切断介质,还可用作调节介质的流量。化工待业的特别需要时,阀体、阀盖内腔可进行搪瓷。用于空间的蝶阀可采用手轮操作,用户需要时,可改用电动或气动操作;特殊埋地蝶阀,用操作杆操作。
Double eccentric end—flanged resilient sealing butterfly valve is operated by the disc rotating from 0℃ to 90℃ can be applied to cut offor regulate the flow of media Vitreous enamel is available upon request valve can be actuated by operating lever,handle wheel,electric actuator or pneumatic actuator
独特的设计Professional design
双偏心软密封蝶阀是一种新型蝶阀,在蝶板全开时橡胶密封环完全脱离金属阀座,因而增加使用寿命。
对于DN l200及以下口径,阀体密封面采用独特的滚压技术,将不锈钢座圈压入阀体内/或堆焊口,而对于大口径(DN≥1 400),则采用超音速喷涂阀体密封面,其结合强度可达50MPa。
橡胶密封圈与蝶板通过压圈作可调节紧固,使密封压缩量控制在最佳状态。
阀体、蝶板材料采用球墨铸铁,保证了18dj18大奖娱乐手机足够强度密封环采用橡胶及阀座圆锥密封面都使密封更可靠。
When initiating the roatry opening movement the disc is off-seated after only a few degree of opening movement and there is very little
wear and tear between seat ring and disc
Stainless steel seat ring is roleed into the valve body by applying special rolling technology when DN≤1200 Ultrasonic spray applies seal of valve body when DN≥1400.
Rubber sealing ring and disc can adjust tightness or softness of sealing with clamping rin9,it insu res best performance of adjusting the compression of sealing
Body and disc made of ductileiron which promote the impact resistance and pressure-bearing capacity;sealing ring made of rubber and valve seat sealing su rface is conical shaped,make the sealing capacity more reliable.
优秀的防腐性能ExcelIent corrosion protection
阀体、蝶板、压圈和支架内外表面喷涂环氧树脂。
Inside electrostatic epoxy resin powder coating or vitreous enamel)
upon request),outside electrostatic epoxy resin powder coating
可靠的卫生性Reliable health nature
环氧树脂和橡胶符合卫生标准GB/Tl 7219-1998。
Epoxy resin powder is up to the health standard GB/Tl7219-1998
适用范围Scope of application
给排水、暖通及燃气系统以及化工、发电、冶金等行业的大型装置上和管线上。
Potable water supply and distribution,electric power plant,gas supply,warm-air system,smeltingplant,chemical industry
设计标准Design standard:DIN3354
连接法兰Flange:DIN2501等效于GB/Tl72416
结构长度Face to face dimensions:长型DIN3202(等效于IS05752)或短型BS51 55
连接中法兰Top flange:IS05211
工作温度Working temperature:丁腈橡胶NBR≤80℃三元乙丙EPDM
≤120℃氟橡胶FPM≤160℃
试验标准Testing standard:DIN3230 0r GB/Tl3927

 卧式安装结构示意图  埋地安装结构示意图

技术性能Technical characteristic

公称通径Nominal diameter DN150-2600mm
公称压力Nominal pressure 1.0MPa 1.6MPa 2.5MPa
壳体试验Strength testing 1.5MPa 2.4MPa 3.75MPa
密封试验Scaling testing 1.1MPa 1.76MPa 2.75MPa

主要零件材料Main components and maeterials

NO. 名称 Name 材料Material
1 阀体、蝶板 body disc QT500-7表面喷涂环氧树脂QT500 with internal and external epoxy resin coating
2 上、下阀杆 stems 不锈钢:1Cr13、1Cr18Ni9Ti 或1Cr17Ni12Mo2Ti Stainless steel min.13%
3 导向套、密封套 bushing 青铜ZCuAL 10Fe3 Bronze ZCuAL 10Fe3
4 密封圈、O型密封圈 Seal ring O-ring 丁腈橡胶、三元乙丙或氟橡胶 NBR、EPDM or FPM